Shiraz University
Iranian Journal of Science and Technology Transactions of Mechanical Engineering
2228-6187
34
2
2010
04
28
Simulation of free surface wave pattern due to the moving bodies
117
134
EN
10.22099/ijstm.2010.906
Steady three-dimensional free surface waves generated by three dimensional moving bodies are presented. By applying Green’s theorem and the Green function method, an integral equation for the perturbation velocity potential is obtained based on the potential flow theory. The method uses constant-strength doublet and source density distribution over the foil body surface and Neumann-type condition. On the undisturbed free surface source density is applied to satisfy the free surface condition that is defined by the first and second order solutions. After solving the doublet on the body and source on the free surface, the computational results of pressure, lift, wave drag, wave pattern and wave elevation can be calculated at various Froude numbers. The results for the surface piercing (such as strut and Wigley hull) and submerged moving hydrofoils have been presented. The validity of the numerical results is examined by comparing it with the experimental results.
Free surface,pressure distribution,lift and drag,wave pattern,Wigley hull
http://ijstm.shirazu.ac.ir/article_906.html
http://ijstm.shirazu.ac.ir/article_906_1b167018046dc0a27c3de495affbd785.pdf
Shiraz University
Iranian Journal of Science and Technology Transactions of Mechanical Engineering
2228-6187
34
2
2010
04
28
A complete treatment of thermo-mechanical ALE analysis; Part I: Formulation
135
148
EN
10.22099/ijstm.2010.907
Arbitrary Lagrangian Eulerian (ALE) finite element method is extensively used for numerical simulation of solid mechanics problem. The versatility of the mesh in ALE approach makes it particularly effective and efficient in solving large deformation problems. In this work, a complete treatment of fully coupled ALE formulation is presented incorporating inertial, rate and thermal effects. The formulation may be used in conjunction with thermo-elasto-viscoplactic material models. A consistent and efficient tangent operator is developed in closed form to handle stress integration. The applications of this formulation are given in the second part of this paper.
Arbitrary Lagrangian Eulerian,Finite element method,large deformation,implicit dynamic analysis,thermo-mechanical,viscoplastic
http://ijstm.shirazu.ac.ir/article_907.html
http://ijstm.shirazu.ac.ir/article_907_29460d72e828b527625e55250004123d.pdf
Shiraz University
Iranian Journal of Science and Technology Transactions of Mechanical Engineering
2228-6187
34
2
2010
04
28
A complete treatment of thermo-mechanical ALE analysis; Part 2: Finite element equations and applications
149
165
EN
10.22099/ijstm.2010.908
In the first part of this paper series, a complete formulation for fully coupled ALE analysis of large deformation solid mechanic problems was developed. The formulation incorporated inertial, rate and thermal effects, and the treatment of rate and temperature dependent constitutive equations were presented. In this part, the ALE equations are discretized to form finite element equations. An algorithm for the treatment of mesh motion is described and example problems are presented to demonstrate the capability of the proposed formulation.
Arbitrary Lagrangian Eulerian,Finite element method,large deformation,implicit dynamic analysis,thermo-mechanical,viscoplastic
http://ijstm.shirazu.ac.ir/article_908.html
http://ijstm.shirazu.ac.ir/article_908_ea1a71982ba265fc6b4ac4b60dc6c305.pdf
Shiraz University
Iranian Journal of Science and Technology Transactions of Mechanical Engineering
2228-6187
34
2
2010
04
28
Durability of a small agricultural engine on biogas/diesel dual fuel operation
167
177
EN
10.22099/ijstm.2010.909
Biogas from anaerobic digestion of organic waste is a potential alternative to the partial substitution of petroleum derived fuels because it is from renewable resources that are widely available. The effect of long term durability tests using biogas/diesel dual fuel operation on wear characteristics is evaluated and presented in this paper. Steady state tests were performed on a small, single cylinder, naturally aspirated, 4-stroke, direct injection diesel engine at a speed of 1500 rpm, coupled to a generator set to generate electricity for over 3500 hours. Lubricating oil samples were collected during the test run and were subjected to the analysis of various wear metal traces present and the changes in their properties. After completion of the endurance test, the engine was dismantled for physical inspection and wear assessment of vital parts. Formation of carbon deposits on in-cylinder surfaces was not found to be problematic. Injector tip coking did not occur. Surface wear and accumulations of metal debris in crankcase lubricating oil samples were analyzed and found to increase with time, but not at an unusual rate. Properties of used lubricating oils did not alter significantly from their original values. Wear was not significantly different in the test engine fueled with the biogas/diesel combination. An overall evaluation of the results indicated that the biogas/diesel duel fuel operation could be substituted for diesel fuel in electricity generation and worked satisfactorily under long term engine operation without any major troubles.
Biogas,compression ignition,dual fuel,endurance test,renewable energy,Wear
http://ijstm.shirazu.ac.ir/article_909.html
http://ijstm.shirazu.ac.ir/article_909_0c4071db88f1e20c741a642ffee710e3.pdf
Shiraz University
Iranian Journal of Science and Technology Transactions of Mechanical Engineering
2228-6187
34
2
2010
04
28
A three-dimensional study of the motion of a drop in plane poiseuille flow at finite Reynolds number
179
196
EN
10.22099/ijstm.2010.910
Three-dimensional simulations are presented on the motion of a neutrally buoyant drop between two parallel plates at a finite-Reynolds-number in plane Poiseuille flow, under conditions of negligible gravitational force. The full Navier-Stokes equations are solved by a finite difference/front tracking method that allows a fully deformable interface between the drop and the suspending medium and the inclusion of the surface tension. In the limit of a small Reynolds number (
Drop,Poiseuille flow,finite difference/front tracking method,capillary number
http://ijstm.shirazu.ac.ir/article_910.html
http://ijstm.shirazu.ac.ir/article_910_ff371bd414e83da62ee2f926df86ba78.pdf
Shiraz University
Iranian Journal of Science and Technology Transactions of Mechanical Engineering
2228-6187
34
2
2010
04
28
Explicit minimum fuel intercept strategy for high-order dynamics
197
213
EN
10.22099/ijstm.2010.911
An optimal fuel guidance strategy with acceleration limit is derived for interception of maneuvering targets. The guidance/control system is assumed as a linear time-varying arbitrary-order and is identical in each channel. An approximate model for drag acceleration is also considered in the solution. The optimal fuel strategy has some detrimental effects in most practical situations, if it is used entirely to the end. This strategy can be used at the beginning of the guidance phase for large initial heading errors in order to quickly reduce it with minimum effort. An explicit guidance law is then developed for minimum and nonminimum phase autopilots in order to modify the undesirable effects of the optimal fuel guidance law.
Intercept guidance,minimum fuel,acceleration limit
http://ijstm.shirazu.ac.ir/article_911.html
http://ijstm.shirazu.ac.ir/article_911_398448083271cac325d657cddc257ce8.pdf
Shiraz University
Iranian Journal of Science and Technology Transactions of Mechanical Engineering
2228-6187
34
2
2010
04
28
Rotor mass effect on nonlinear dynamic behavior of aerodynamic noncircular journal bearing systems
215
230
EN
10.22099/ijstm.2010.912
This paper presents the effect of rotor mass on nonlinear dynamic behavior of a rigid rotor supported by aerodynamic noncircular journal bearings. A finite element method has been employed to solve the Reynolds equation in static and dynamical states and the dynamical equations are solved using Runge-Kutta method. To analyze the behavior of the rotor center in horizontal and vertical directions under different operating conditions, dynamic trajectory, power spectra, Poincare maps and bifurcation diagrams are used. Results of this study reveal how the complex dynamic behavior of two types of noncircular bearing systems comprising periodic and -periodic responses of the rotor center varies with changes in rotor mass values.
Aerodynamic noncircular bearing,rotor mass,poincare map,Bifurcation
http://ijstm.shirazu.ac.ir/article_912.html
http://ijstm.shirazu.ac.ir/article_912_b1d792f1830a5ffca6b1d6a0ea50c4a6.pdf
Shiraz University
Iranian Journal of Science and Technology Transactions of Mechanical Engineering
2228-6187
34
2
2010
04
28
Influence of particle size on corrosion resistance of electroless Ni-P-SiC composite coatings
213
234
EN
10.22099/ijstm.2010.913
High phosphorus electroless nickel bath has been used to prepare composite coatings containing SiC particles (40 nm, 3 mm and 7 mm). The coated samples were subjected to heat treatment at 400 °C for 1h. The effect of heat treatment on the microstructure of Ni-P-SiC composite coatings was investigated by X-ray diffraction. Potentiodynamic polarization measurements made on these deposits in 3% sodium chloride solution showed that corrosion resistance in nano-composite coatings was much higher than micro-composite coatings. The corrosion rate results for nano-composite coatings showed a 6 fold improvement as compared to the micro-composite coatings.
Particle size,Ni-P-SiC,electroless,corrosion resistance
http://ijstm.shirazu.ac.ir/article_913.html
http://ijstm.shirazu.ac.ir/article_913_a0fa34929684f2ffde21c1be8d0e7c5f.pdf